Chemical Testing Kits

Chlorine is the most widely used oxidizing biocide today for disinfection of domestic water supplies as also for the removal of tastes and odours from water. The amount of chlorine required to be added in a water system is determined by chlorine demand contact time ph and temperature of the water. Chlorine residual in drinking water indicates that disinfection has been achieved by chlorine and bacteria / viruses that cause diarrheal disease have been eliminated. Also the water is protected from recontamination during storage. Our AQUASOL single reagent based Free Chlorine Test Kit (O.T.) comes with a scientifically designed Colour Comparator. The economical Comparator based design not only discern colours easily but also helps to achieve results quickly. This Free Chlorine Test Kit (AE-409) is a cost effective and convinent method for periodic monitoring free chlorine in water.. The end point is very sharp and easily discernable by the user. Even a shop floor worker will be able to get desired results with our test kit.

When water passes through or over deposits such as limestone the levels of ca2+ mg2+ and hco3 ions present in the water greatly increase and cause the water to be classified as hard water. Hardness in water is caused by dissolved minerals and calcium and magnesium ions are usually present in significant concentration along with other divalent ions. Hardness creates scale deposit problem which lead to energy loss in different industrial systems such as boiler cooling system cause scale formation in plumbing heating appliances and boilers. Measuring total hardness is essential to monitor – softener demineralization RO plant softening processes etc. Our AQUASOL AE201 hardness range is one of the largest available in the market today. It is a premium kit and finds use in almost all industries where water is the most important ingredient/parameter.

Calcium hardness is caused by the presence of calcium ions in the water. Calcium salts can be readily precipitated from water and high levels of calcium hardness tend to promote scale formation in the water system. Calcium hardness is an important control test in industrial water systems such as boilers and steam raising plants. Our Aquasol AE202 kit tests even low levels of calcium in water.

Chloride ions are one of the major inorganic anions in water and wastewater. Although high concentrations of chloride in water are not known to be toxic to humans they may corrode metal pipes. It is essential to monitor chloride concentration in boiler systems to prevent damage of metal parts. In high levels chloride can corrode stainless steel and be toxic to plant life. Therefore chloride is one of the very important parameters which is frequently tested and our AQUASOL AE203 kit makes testing easy simple at the same time accurate.

The alkalinity of water is capacity of water to neutralise acid to desired ph. It is mainly a sum of carbonate bicarbonate and hydroxide ions. Salts of weak acids like borate silicate and phosphate may also contribute to alkalinity. Alkalinity is important in the treatment of potable water waste water boiler and cooling water. Our Aquasol AE204 alkalinity kit is very easy to use test to gives reliable results.

Chlorine is the most widely used oxidizing biocide today for disinfection of domestic water supplies as also for the removal of tastes and odours from water. The amount of chlorine required to be added in a water system is determined by chlorine demand contact time ph and temperature of the water. Chlorine residual in drinking water indicates that disinfection has been achieved by chlorine and bacteria / viruses that cause diarrheal disease have been eliminated. Also the water is protected from recontamination during storage. Our AQUASOL AE205 chlorine test is available as DPD method and the kit gives very reliable results. The end point is very sharp and easily discernable by the user. Even a shop floor worker will be able to get desired results with our test kit.

Nitrites occur in water as an intermediate product in the biological breakdown of organic nitrogen being produced either through the oxidation of ammonia or the reduction of nitrate. The presence of large quantities of nitrites is indicative of waste water pollution. Low range nitrite estimation is useful for drinking water analysis. Nitrite is added to control corrosion in closed cooling systems. We have two kits for nitrite one a very low range especially for drinking and the higher one for waste water. Our AQUASOL AE207 kits are based on colour comparison and are very simple and convenient to use.

Sulphate is a constituent of TDS and may form salts with sodium potassium magnesium and other cations. Sulphate (so4-2) is widely distributed in nature and may be present in natural waters at concentrations ranging from a few to several hundred milligrams per litre. Sulphate can cause scale build-up in water pipes. Sulphates are also food for theAnaerobic slime formers the sulphate reducing bacteria which are responsible for pitting type of corrosion in pipes.The AQUASOL water test kit for sulphate is based on titrimetry and is extremely user friendly.

When water passes through or over deposits such as limestone the levels of ca2+ mg2+ and hco3 ions present in the water greatly increase and cause the water to be classified as hard water. Hardness in water is caused by dissolved minerals and calcium and magnesium ions are usually present in significant concentration along with other divalent ions. Hardness creates scale deposit problem which lead to energy loss in different industrial systems such as boiler cooling system cause scale formation in plumbing heating appliances and boilers. Measuring total hardness is essential to monitor – softener demineralization RO plant softening processes etc. Our AQUASOL AE201 hardness range is one of the largest available in the market today. It is a premium kit and finds use in almost all industries where water is the most important ingredient/parameter.

Calcium hardness is caused by the presence of calcium ions in the water. Calcium salts can be readily precipitated from water and high levels of calcium hardness tend to promote scale formation in the water system. Calcium hardness is an important control test in industrial water systems such as boilers and steam raising plants. Our Aquasol AE212 kit tests even high levels of calcium in water.

Chloride ions are one of the major inorganic anions in water and wastewater. Although high concentrations of chloride in water are not known to be toxic to humans they may corrode metal pipes. It is essential to monitor chloride concentration in boiler systems to prevent damage of metal parts. In high levels chloride can corrode stainless steel and be toxic to plant life. Therefore chloride is one of the very important parameters which is frequently tested and our AQUASOL AE213 kit makes testing easy simple at the same time accurate.

Chloride ions are one of the major inorganic anions in water and wastewater. Although high concentrations of chloride in water are not known to be toxic to humans they may corrode metal pipes. It is essential to monitor chloride concentration in boiler systems to prevent damage of metal parts. In high levels chloride can corrode stainless steel and be toxic to plant life. Therefore chloride is one of the very important parameters which is frequently tested and our AQUASOL AE213L kit makes testing easy simple at the same time accurate.

The alkalinity of water is capacity of water to neutralise acid to desired ph. It is mainly a sum of carbonate bicarbonate and hydroxide ions. Salts of weak acids like borate silicate and phosphate may also contribute to alkalinity. Alkalinity is important in the treatment of potable water waste water boiler and cooling water. Our Aquasol AE214 alkalinity kit is very easy to use test to gives reliable results.

Chlorine is the most widely used oxidizing biocide today for disinfection of domestic water supplies as also for the removal of tastes and odours from water. The amount of chlorine required to be added in a water system is determined by chlorine demand contact time ph and temperature of the water. Chlorine residual in drinking water indicates that disinfection has been achieved by chlorine and bacteria / viruses that cause diarrheal disease have been eliminated. Also the water is protected from recontamination during storage. Our AQUASOL AE215 chlorine test is available as DPD method and the kit gives very reliable results. The end point is very sharp and easily discernable by the user. Even a shop floor worker will be able to get desired results with our test kit.

Nitrites occur in water as an intermediate product in the biological breakdown of organic nitrogen being produced either through the oxidation of ammonia or the reduction of nitrate. The presence of large quantities of nitrites is indicative of waste water pollution. Low range nitrite estimation is useful for drinking water analysis. Nitrite is added to control corrosion in closed cooling systems. We have two kits for nitrite one a very low range especially for drinking and the higher one for waste water. Our AQUASOL AE217 kits are based on colour comparison and are very simple and convenient to use.

Sulphate is a constituent of TDS and may form salts with sodium potassium magnesium and other cations. Sulphate (so4-2) is widely distributed in nature and may be present in natural waters at concentrations ranging from a few to several hundred milligrams per litre. Sulphate can cause scale build-up in water pipes. Sulphates are also food for theAnaerobic slime formers the sulphate reducing bacteria which are responsible for pitting type of corrosion in pipes.The AQUASOL water test kit for sulphate is based on titrimetry and is extremely user friendly.

When water passes through or over deposits such as limestone the levels of ca2+ mg2+ and hco3 ions present in the water greatly increase and cause the water to be classified as hard water. Hardness in water is caused by dissolved minerals and calcium and magnesium ions are usually present in significant concentration along with other divalent ions. Hardness creates scale deposit problem which lead to energy loss in different industrial systems such as boiler cooling system cause scale formation in plumbing heating appliances and boilers. Measuring total hardness is essential to monitor – softener demineralization RO plant softening processes etc. Our AQUASOL AE221 hardness range is one of the largest available in the market today. It is a premium kit and finds use in almost all industries where water is the most important ingredient/parameter.

Nitrites are salts of nitrous acid which occur naturally or artificially in ground water. They are released in water from Fertilizer runoff water sewage and mineral deposits.High levels of Nitrite are toxic to mammals and other lower forms like marine species. They disturb the oxygen delivering ability ofhemoglobin in the bloodstream. Also large blooms of Algae can grow due to high Nitrite level leading to hypoxia. Hypoxia dead zones created are deadly to almost all marine species. Therefore regularly monitoring of Nitrite levels is very essential and needs to be done judiciously in fresh water.

When water passes through or over deposits such as limestone the levels of ca2+ mg2+ and hco3 ions present in the water greatly increase and cause the water to be classified as hard water. Hardness in water is caused by dissolved minerals and calcium and magnesium ions are usually present in significant concentration along with other divalent ions. Hardness creates scale deposit problem which lead to energy loss in different industrial systems such as boiler cooling system cause scale formation in plumbing heating appliances and boilers. Measuring total hardness is essential to monitor – softener demineralization RO plant softening processes etc. Our AQUASOL AE231 hardness range is one of the largest available in the market today. It is a premium kit and finds use in almost all industries where water is the most important ingredient/parameter.

hen water passes through or over deposits such as limestone the levels of ca2+ mg2+ and hco3 ions present in the water greatly increase and cause the water to be classified as hard water. Hardness in water is caused by dissolved minerals and calcium and magnesium ions are usually present in significant concentration along with other divalent ions. Hardness creates scale deposit problem which lead to energy loss in different industrial systems such as boiler cooling system cause scale formation in plumbing heating appliances and boilers. Measuring total hardness is essential to monitor – softener demineralization RO plant softening processes etc. Our AQUASOL AE241 hardness range is one of the largest available in the market today. It is a premium kit and finds use in almost all industries where water is the most important ingredient/parameter.

Chlorine is the most widely used oxidizing biocide today for disinfection of domestic water supplies as also for the removal of tastes and odours from water. The amount of chlorine required to be added in a water system is determined by chlorine demand contact time ph and temperature of the water. Chlorine residual in drinking water indicates that disinfection has been achieved by chlorine and bacteria / viruses that cause diarrheal disease have been eliminated. Also the water is protected from recontamination during storage. Our AQUASOL AE246 chlorine test is available Iodometric method and this kit gives very reliable results. Even a shop floor worker will be able to get desired results with our test kit.

Chlorine is the most widely used oxidizing biocide today for disinfection of domestic water supplies as also for the removal of tastes and odours from water. The amount of chlorine required to be added in a water system is determined by chlorine demand contact time ph and temperature of the water. Chlorine residual in drinking water indicates that disinfection has been achieved by chlorine and bacteria / viruses that cause diarrheal disease have been eliminated. Also the water is protected from recontamination during storage. Our AQUASOL AE246L chlorine test is available Iodometric method and this kit gives very reliable results. Even a shop floor worker will be able to get desired results with our test kit.